Available depth sizes are 12″, 15″ & 18″.  Comes with two mounting brackets and a load beam. The load beam is only for the 60″, 72″ & 96″ shelves.

• Shelf material can be the same material used on the work surface, however, you need to specify when placing the order
• Load bearing capacity 250 lbs evenly distributed
• Heavier load capacity shelves are available
• PB shelves are adjustable in 1″ increments
• Shelves come in ESD & Standard laminate
• Clean Room underseal on all laminate shelving is available

Available depth sizes are 12″, 15″, & 18″.  Comes with front lip and two brackets.

• All PB shelves are adjustable in 1″ increments
• Both style shelves can be tilted forward 15%
• All shelves come with load bearing shelf support,  300 lb load rated, evenly distributed
• Extra heavy duty shelves are available

12″ deep

• Shelves are made of heavy gauge wire
• Finished with a silver zinc epoxy powder coat
• All wire shelves come with a 1″ front wire lip
• 50 lb load rating evenly distributed
• PB shelves can tilt 15 degrees forward

• The split shelf design provides additional shelving and/or other hang-on accessories where needed.
• Mounts to the inside uprights of PB benches
• Overhead Hutches, Electrical Channel, Shelves and other accessories can all mount to the frame
• All WSI accessories can mount to a split shelf unit. Single sided split shelf frames mount on one side only. Double sided frames can have accessories mounted on both sides.

All steel cabinets are made of heavy duty 18 gauge steel

• Doors are double lined on the inside & outside for quiet operation
• Hinges are stainless steel industrial insertional 180 degree five knuckle hinges
• All doors come with one lock
• Dual roller magnetic catch to keep the doors closed
• 100% epoxy baked on powder paint
• Available widths: 18″, 24″, 30″, 36″, 42″
• Available heights: 24″, 30″, 36″, & 48″
• Optional glass hinged door inserts available
• Sliding glass doors also available
• Cabinets come with a tubular frame for mounting to the uprights for a Production Bench and C2 bench. Tubular frame applies to benches that are grater than 48″ wide (2) 30″ for a 60″ bench. (2) 36″ cabinets for a 72″ bench. (2) 48″ cabinets for a 96″ bench

All steel cabinets are made of heavy duty 18 gauge steel

• Doors are double lined on the inside & outside for quiet operation
• Hinges are stainless steel industrial insertional 180 degree five knuckle hinges
• All doors come with one lock
• Dual roller magnetic catch to keep the doors closed
• All cabinets are SEFA compliant
• 100% epoxy baked on powder paint
• Available widths: 18″, 24″, 30″, 36″, 42″
• Available heights: 24″, 30″, 36″, & 48″
• Optional glass hinged door inserts available
• Sliding glass doors also available
• Cabinets come with a tubular frame for mounting to the uprights for a Production Bench and C2 bench. Tubular frame applies to benches that are grater than 48″ wide (2) 30″ for a 60″ bench. (2) 36″ cabinets for a 72″ bench. (2) 48″ cabinets for a 48″ bench

All WSI electrical options have been certified by UL and are inspected on a monthly basis for installation practices and component consistency

• Work surface mounted fits between uprights
• Size 24″, 36″ & 48″ lengths
• 8′ power cord is standard. 10′ or 15′ power cords are optional
• 8 outlets 15amp is standard. Optional 20 amp available
• On off switch – Circuit breaker

• EL-4 electrical can be mounted in the front or rear of the bench. It can also be mounted to the worksurface
• Comes with 8 outlets and 15 amp power
• 8′ power cord

• EL-3 electrical can be mounted in the front or rear of the bench to the front or rear beam. It can also be mounted to the worksurface
• Comes with  8 outlets and 15 amp power
• 8′ power cord

• EL-2 has six electrical outlets mounted in the front face of each riser box
• Qty (1) electrical panel and the other riser box side is open
• Cover panel (CP) is optional

• Utility duct way (UDW) with data, air or gas shielded partitions
• The utility chase mounts above the work surface and in between the uprights and can be interconnected from upright to upright, and bench to bench
• It can also be mounted to the worksurface
• UDW can also be used above doorways to continue flow of cables & wires with no interruptions
• UL Listed when ordered with the PB bench
• Comes with the cover

Utility duct way mounts under the work surface to manage cables

• Our C2 Power Pole attaches to any new or existing C2 upright.
• Wires drops from the ceiling.
• Comes standard with a conduit landing bracket for utilities, (Power, Data, Air or Gas) to tie into and cover shroud
• Shroud is used to cover the gap between the top of the power pole & ceiling
• Power pole comes within 3” short of the ceiling, specify height of ceiling when ordering.

For interconnecting air from bench to bench.

• Mounts in front beam
• Hostler mount ADSH-PB comes with one female coupler, interconnecting hose, and pigtail hose for incoming source
• Coupler can be mounted to the front beam
• Coupler can be purchased separately

Overhead lighting fixture with light housing and prismatic lens

• Available in 36″, 48″, 60″, 72″ & 96″ widths
• Standard overhead light is 48″ and has one on/off switch, 8ft power cord and a circuit breaker
• LED light bulb is the standard light fixture. According to new laws, fluorescent ballast type lights are no longer available
• Wattage per LED light – 24″ = 15W, 36″ = 25W, 48″ = 30W
• Prismatic lens
• LED power efficiency is 85% and 30K – 50K hour life span
• All sizes of light fixtures come in double tube, single tube or as an under counter light fixture
• Bulbs sold separately. 24″, 36″ or 48″ bulbs.

• Under counter light are available in 36″ and 48″ sizes. LED lights are now the standard light fixture. Florescent bulbs are no longer available

Our Economy light fixture is a great option for businesses on a tight budget

• Available in 36″, 48″, 72″ & 96″ widths
• When purchasing our Economy lights, you must have a production workbench with slotted uprights already. Brackets for mounting light come with the purchase of the production Bbnch and slotted uprights
• Comes with a lens wrap
• Uses LED bulbs which are not included
• The 96” Economy light for 96″ benches consists of (2) 48 inch lights with (1) on/off swtich, L brackets, light mounting bar and 8ft. power cord

• Fully articulating swing are that moves side to side and up and down
• Can be mounted to the worksurface and slotted uprights

• Holds up to a 19″ monitor
• Swing Arm is 10″ in lenght
• Shown here with the extension arm attached

• Extension arm attached to the Flat Screen Monitor Arm
• Adds an additional 8″ in lenght
• Two arms allow for 180 degrees of rotation
• Loosen bolts to move up and down
• Holds 19″ monitor
• Purchase a double arm and receive 10″ arm, 8″ arm, 3 knuckles, 1 mounting bracket and 1 hinged panel bracket for connecting arms together and mounting

• Used to hold, laptop, tools, paper etc.
• Steel surface
• 12″ x 12″ with lower lip at bottom

• Uses the Flat Screen Monitor Arm and then WSI adds a keyboard option and arm to mount the monitor.

• Standard high pressure laminate is used on all standard work benches, work surfaces shelves and carts.
• Impact resistant
• 180 degree rolled Ergo front edge
• 1.125″ thick industrial grade particle board under core
• Sealed on bottom to prevent warping

HPL Laminate Data Sheet

• High impact resistant laminate
• Ergo 180 degree front rolled edge
• 1.125″ thick industrial grade partial board
• Dissipation level is greater than 10/6th, but less than 10/9th
• Banana Jacks are optional

ESD Laminate Data Sheet

• 18ga #304 stainless steel
• 3/16 front edge radius
• Brush finish
• #316 Stainless is option if anti-rust is needed
• Standard substrate finish is load bearing and hat sections are mounted under the surface to take out any deflection
• Glued over a 1.125″ thick particle board under core. This is an optional up charge

316 Stainless Steel Data Sheet

304 Stainless Steel Data Sheet

• 3/4″ thick surface
• 3/16 bevel edge on all sides
• Chemical and water resistant, see spec sheet for Chemical Resistance

Phenolic Resin Data Sheet – Trespa Athlon

Phenolic Resin Data Sheet – Trespa Top Lab

• 1″ thick
• Resistant against harsh chemicals
• Heat resistant

Epoxy Resin Data Sheet

• Chemical resistant HPL laminate
• High impact resistant
• All edges are squared
• 1.125 tick particle board under core
• Surface is sealed on bottom to prevent warping

Chemical Laminate Data Sheet

• Anti bacteria
• 1/2″ thick
• 1″ front edge build-up
• Ergo rolled edge

• The Footrest Tube can be used on both the C2 or PB bench. You must specify which type of bench the tube is for as they mount differently.

• The footrest tube is 1” round heavy duty steel tubing and is finished in a bright zinc
• Ergo pan is made in two different widths 24″ and 40″ wide.  24″ pan is for 36″ and 48′ wide benches
• PB footrest tube adjusts in/out
• The footrest pan is a formed steel pan lined with a non slip friction tape
• The Pan tilts up/down for operator comfort.

• Independent adjustments for foot pan height and angle
• Heavy-gauge steel base with non-skid rubber floor glides on base and non–ABS friction tape on foot pan
• Acceptable for Clean room applications

Made of heavy gauge steel, and formed for strength, comes with a front lip so the CPU will not slide out while the work bench is being transported. CPU comes in two different configurations, (1) fixed platform and can attached to any WSI PB workbench or any four legged bench, simply attached to leg frame using heavy duty self tapping sheet metal screws. (2) Adjustable CPU holder, the platform can be adjusted from 6″ – 9″ wide

• Fixed CPU holder 8″w x 18″d x 11″h

• Adjustable CPU Holder 6″ – 9″ w x 18″d x 20″h

There are several caster option to choose from, all caster are 1.25″ x 4″

All casters carry a load rating of 1,000 lbs combined when using all four casters

• Total locking caster, lock the roll and the swivel
• Mount to bench frame as fixed hgt or adj 30″ – 36″
• Locking the swivel and locking the roll
• Used for equipment testing and adj, bench applications

There are several caster option to choose from, all caster are 1.25″ x 4″ (5″ overall hgt with mounting hub)

All casters carry a load rating of 1,000 lbs combined when using all four casters

• 4″ Standard Caster, swivel w/(2) locking
• 5″ overall hgt including the mounting hub
• Available as a fixed bench, specifiy height, or cart or adjustable 30″ – 36″
• Swivel with or without locks. You can also lock all 4 wheels

There are several caster option to choose from, all caster are 1.25″ x 4″

All casters carry a load rating of 1,000 lbs combined when using all four casters

• Adjustable and leveling caster, 2 x 2, will adjust to level out the bench
• 1,ooo load capacity

This caster is used for all mobile cabinets, (2 locking)

• Load rating per all four casters 600 lbs
• Comes with flat plate attachment
• Nut and bolt hardware attachment

• Steel peg board, 24″ high. Available sizes are 36″ – 72″
• Color will match the bench color or be painted using any one of our standard colors
• 4″ to 6″ non-perforated on all sides

• Multi bin Ergo parts cup rail 6″ high, comes with two mounting brackets
• Bins available in 6″, 12″ and 18″
• Sizes range from 48″ – 72″

• Single Parts Cup Rail 1.5″ high, comes with 2″ mounting brackets for the PB Series Bench
• Sizes range from 48″ – 96″

• Tool Trolly with hanger includes two mounting brackets
• Heavy duty roller hanger also available as an upgrade
• Available sizes are 48″ – 72″
• Shown with optional tool balancer