Available depth sizes are 12″, 15″ & 18″.  Comes with two mounting brackets and a load beam. The load beam is only for the 60", 72" & 96" shelves.

• Shelf material can be the same material used on the work surface, however, you need to specify when placing the order
• Load bearing capacity 250 lbs evenly distributed
• Heavier load capacity shelves are available
• C2 shelves are infinitely adjustable
• Shelves come in ESD & Standard laminate
• Clean Room underseal on all laminate shelving is available

Available depth sizes are 12″, 15″, & 18″.  Comes with front lip and two brackets.

• All C2 shelves are infinitely adjustable,
• Both style shelves can be tilted forward 15%,
• All shelves come with load bearing shelf support,  300 lb load rated, evenly distributed
• Extra heavy duty shelves are available

12″ deep

• Shelves are made of heavy gauge wire
• Finished with a silver zinc epoxy powder coat
• All wire shelves come with a 1″ front wire lip
• 50 lb load rating evenly distributed
• C2 shelves can tilt 15 degrees forward

• The split shelf design provides additional shelving and/or other hang-on accessories where needed.
• Mounts to the inside uprights of C2 benches
• Overhead Hutches, Electrical Channel, Shelves and other accessories can all mount to the frame
• All WSI accessories can mount to a split shelf unit. Single sided split shelf frames mount on one side only. Double sided frames can have accessories mounted on both sides.

Steel Double Door unit is constructed of heavy gauge steel

• All doors come with two inserted plastic cup pull handles. Optional lab grade aluminum available
• Door locks are not standard but are available
• Available sizes are, 36″, 48″, 60″ & 72″

Steel Flipper Door Hutch unit is constructed of heavy gauge steel

• Door retracts and slides inside the cabinet.
• All doors come with two inserted plastic handle for easy lift
• All doors come with one lock
• Available sizes are, 36″, 48″, 60″ & 72″
• Cabinets come with two mounting brackets
•  (2) 48″ hutches are used for 96″ bench

All WSI electrical options have been certified by UL and are inspected on a monthly basis for installation practices and component consistency

• Work surface mounted fits between uprights
• Size 24", 36" & 48" lengths
• 8', 10' or 15' power cords available
• 8 outlets 15 & 20 amp
• On off switch.

Our DEC-1 & DEC-2 Panels are equipped with Standard 20A or 15A outlets

Optional upgrades are available:

• Gray outlets: Unlimited Power Source (UPS) 20A or 15A
• Orange outlets: Emergency Back-up Power 20A or 15A
• Data ports can be upgraded at time of order
• GFI 30A poer configuration can be added to the DEC-1 Upgraded box

• Comes with 6 15A outlets in a single panel mounted box
• DEC-2 provides two DEC-1 outlet panels mounted in each upright. Total of 12 outlets. Both DEC's can mount on one side of an upright or on each upright.They can mount above or below the work surface
• You can upgrade to 20A outlets and power cord or to a multiple circuit system. 2 or 4 circuits (each circuit is labeled) are recommended when installing a run of benches

• 15 or 20 amp power
• Single or two-phase power
• Mounts to production bench slotted uprights or Concept 2000 uprights
• 16 gauge steel
• Painted to match frame color
• UL Listed

• International plug options

• Utility duct way (UDW) with data, air or gas shielded partitions
• The utility chase mounts above the work surface and in between the uprights and can be interconnected from upright to upright, and bench to bench
• UDW can also be used above doorways to continue flow of cables & wires with no interruptions
• UL Listed when ordered with the C2 bench
• Comes with the cover

Utility duct way mounts under the work surface to manage cables from upright to upright.

• Our C2 Power Pole attaches to any new or existing C2 upright.
• Wires drops from the ceiling.
• Comes standard with a conduit landing bracket for utilities, (Power, Data, Air or Gas) to tie into and cover shroud
• Shroud is used to cover the gap between the top of the power pole & ceiling
• Power pole comes within 3” short of the ceiling, specify height of ceiling when ordering.

For interconnecting air from bench to bench.

• Mounts in front beam
• Hostler mount ADSH-C2 comes with one female coupler, interconnecting hose, and pigtail hose for incoming source
• Coupler can be purchased separately

• Integrated into the DEC-1 box upright or power pole with data shielding
• Specify Cat5 or Cat6 and length of patch if you want WSI to provide you with the patch cords or just the port opening and shielding in the upright DEC- Box.
• Gas Turrets are available in single and double configuerations

Overhead lighting fixture with light housing and prismatic lens

• Available in 24", 36", 48" widths
• Wattage per LED light - 24" = 15W, 36" = 25W, 48" = 30W
• Prismatic lens
• According to new laws, fluorescent ballast type lights are no longer available
• LED power efficiency is 85% and 30K - 50K hour life span
• All sizes of light fixtures come in double tube, single tube or as an under counter light fixture
• Bulbs sold separately. 24", 36" or 48" bulbs.

• Under counter light are available in 36″ and 48″ sizes. Only LED lights are available.

• Basic single swivel arm that can mount to a C2 upright or other modular bench uprights
• Single 10″ arm comes with a mounting bracket and hinged panel bracket
• Basic arms just swing in and out
• If used for other uprights that are different than WSI's, further information will be required

• Holds up to a 19" monitor
• Swing Arm is 10" in lenght
• Shown here with the extension arm attached

• Extension arm attached to the Flat Screen Monitor Arm
• Adds an additional 8" in lenght
• Two arms allow for 180 degrees of rotation
• Loosen bolts to move up and down
• Holds 19" monitor
• Purchase a double arm and receive 10" arm, 8" arm, 3 knuckles, 1 mounting bracket and 1 hinged panel bracket for connecting arms together and mounting

• Used to hold, laptop, tools, paper etc.
• Steel surface
• 12" x 12" with lower lip at bottom

• Uses the Flat Screen Monitor Arm and then WSI adds a keyboard option and arm to mount the monitor.

• Standard high pressure laminate is used on all standard work benches, work surfaces shelves and carts.
• Impact resistant
• 180 degree rolled Ergo front edge
• 1.125″ thick industrial grade particle board under core
• Sealed on bottom to prevent warping

• High impact resistant laminate
• Ergo 180 degree front rolled edge
• 1.125″ thick industrial grade partial board
• Dissipation level is greater than 10/6th, but less than 10/9th

• 18ga #304 stainless steel
• 3/16 front edge radius
• Brush finish
• #316 Stainless is option if anti-rust is needed
• Standard substrate finish is load bearing and hat sections are mounted under the surface to take out any deflection
• Glued over a 1.125″ thick particle board under core. This is an optional upcharge

• 3/4″ thick surface
• Chemical and water resistant, see spec sheet for Chem resistance
• Fore more detailed specifications see our Resources Section under Work Surface Data Sheets

• 1″ thick
• 3/16″ front chamfered edge
• Resistant against harsh chemicals
• Heat resistant
• Fore more detailed specifications see our Resources Section under Work Surface Data Sheets

• Chemical resistant HPL laminate
• High impact resistant
• All edges are squared
• 1.125 tick particle board under core
• Surface is sealed on bottom to prevent warping

• Anti bacteria
• 1/2″ thick
• 1″ front edge build-up
• Ergo rolled edge

• For the Concept 2000 line only
•  Must specificy C2 or PB bench

• The footrest tube is 1” round heavy duty steel tubing and is finished in a bright zinc
• Ergo pan is made in two different widths 24″ and 40″ wide.  24″ pan is for 36″ and 48′ wide benches
• C2 footrest tube adjusts in/out and up/down.
• The footrest pan is a formed steel pan lined with a non slip friction tape
• The Pan tilts up/down for operator comfort.

• Independent adjustments for foot pan height and angle
• Heavy-gauge steel base with non-skid rubber floor glides on base and non–ABS friction tape on foot pan
• Acceptable for Clean room applications

Made of heavy gauge steel, and formed for strength, comes with a front lip so the CPU will not slide out while the work bench is being transported. CPu come in two different configurations, (1) fixed platform and can attached to any WSI C2 workstation or any four legged bench, simply attached to leg frame using heavy duty self tapping sheet metal screws. (2) Adjustable CPU holder, the platform can be adjusted from 6″ – 9″ wide

• Fixed CPU holder 8″w x 18″d x 11″h

• Adjustable CPU Holder 6″ – 9″ w x 18″d x 20″h

There are several caster option to choose from, all caster are 1.25″ x 4″

All casters carry a load rating of 1,000 lbs combined when using all four casters

• Total locking caster, lock the roll and the swivel
• Mount to bench frame as fixed hgt or adj 30″ – 36″
• Locking the swivel and locking the roll
• Used for equipment testing and adj, bench applications

There are several caster option to choose from, all caster are 1.25″ x 4″ (5″ overall hgt with mounting hub)

All casters carry a load rating of 1,000 lbs combined when using all four casters

• 4″ Standard Caster, swivel w/(2) locking
• 5″ overall hgt including the mounting hub
• Available as a fixed bench or cart or adjustable 30″ – 36″
• Swivel with or without locks. You can also lock all 4 wheels

There are several caster option to choose from, all caster are 1.25″ x 4″

All casters carry a load rating of 1,000 lbs combined when using all four casters

• Adjustable and leveling caster, 2 x 2, will adjust to level out the bench, 800 load capacity

This caster is used for all mobile cabinets, (2 locking)

• Load rating per all four casters 600 lbs
• Comes with flat plate attachment
• Nut and bolt hardware attachment

• Steel peg board, 24″ high. Available sizes are 36″ – 72″
• Color will match the bench color or be painted using any one of our standard colors
• 4" to 6" non-perforated on all sides

• Multi bin Ergo parts cup rail 6″ high, comes with two mounting brackets
• Sizes range from 48″ – 72″

• Single Parts Cup Rail 1.5″ high, comes with 2″ mounting brackets for the C2 Series Bench
• Sizes range from 48″ – 96″

• Tool Trolly with hanger includes two mounting brackets
• Heavy duty roller hanger also available as an upgrade
• Available sizes are 48″ – 72″

• • 18 gauge cold rolled steel or stainless steel
  • 24" - 96" wide x 6" and 12" in height
  • Powder coated to match frame color
  • Rail can be mounted to Production Bench slotted uprights or C2 uprights

2000 Series Three Paddle Production Chair is a fully adjustable ergonomic chair. The seat and back tilts and adjusts independent of each other. Production Chair seat and backrest are manufactured with  molded contour foam and have been ANSI/BIFMA tested and certified .

This chair is warrantied for 7 years.

See Complete Details

1000 Series Chair (two paddle)is an adjustable ergonomic chair. The seat adjusts up and down, the backrests has an deluxe tension tilt adjustment. This chair is warranted for 7-years, see warranty statement.

See Complete Details

700 Series Single Paddle ESD or Standard Polyurethane Seating is our basic  Industrial Chair.

The 700 Series Chairs are specifically designed for long term seating and lasting use in the toughest working environment. Furthermore, the polyurethane series chairs are designed with ergonomics as the prevailing feature, these chairs improve productivity and reduce body fatigue due to long term seating.

See Complete Details

500 Series Chair Single Paddle is our most economical chair.

Medium density 2.5”thick foam for both the backrest and the seat.Production Chair has been ANSI/BIFMA tested and certified . This chair is warrantied for 7 years.

See Complete Details